How to flash MeshCore onto a radio
Most LoRa radios ship with Meshtastic on them. To use MeshCore instead, you replace the firmware. It takes about five minutes, a USB cable and a web browser. Nothing to install.
This is how I do it, and which radios I would buy. If you're not sure which of the two you want, I compared them in Meshtastic vs MeshCore.
Which radio to buy
Every radio below is on the official MeshCore flasher. Buy the version for your region: 915 MHz in the US, Canada and Australia, 868 MHz in Europe and the UK. Prices are approximate.
| Radio | About | Good for | Buy |
|---|---|---|---|
| Heltec V3 | $20 | The cheapest way to start. A bare board with a small screen. You add a battery and a case. | Heltec · Amazon |
| Heltec V4 | $20–30 | The newer Heltec. More transmit power, a solar input and a GPS connector. Same price as the V3, so buy this one. | Heltec · Amazon |
| Elecrow ThinkNode M1 | $60–75 | A finished pocket radio: case, battery, GPS and an e-paper screen. The battery lasts for days. | Elecrow · Amazon |
| Seeed SenseCAP T1000-E | $40 | The size of a credit card, waterproof, no screen. Lives in a wallet or on a keychain. | Seeed · Amazon |
| RAK WisBlock starter kit | $35–40 | Very low power. The usual choice for a solar repeater on a roof. | RAK · Amazon |
| Heltec T114 | $25–35 | A cheap low-power board, a good repeater or a long-lasting companion. | Heltec · Amazon |
| LilyGO T-Deck Plus | $80 | A radio with its own keyboard and screen. Works without a phone. | LilyGO · Amazon |
If you just want one radio to carry, get a ThinkNode M1 or a T1000-E. If you want something cheap to try it out, get a Heltec V4.
Two things to know:
- The Heltec V3's Bluetooth antenna is a tiny coil, and it only reaches a few feet.1 Fine on a desk next to your phone. Annoying in a pocket.
- Buy the T1000-E made for Meshtastic, not the LoRaWAN version. The flasher warns that MeshCore can permanently brick the LoRaWAN one.
Amazon is the fastest way to get one in the US. Rokland also stocks most of these.
What you need
- The radio, with its antenna screwed on. Never power a radio without its antenna.
- A USB cable that carries data, not just charge.
- A computer with Chrome or Edge. The flasher uses Web Serial, which Safari, Firefox and phones don't have.
Flashing it
- Plug the radio into the computer.
- Open flasher.meshcore.io in Chrome or Edge.
- Pick your radio from the list.
- Pick a role:
- Companion (Bluetooth) pairs with your phone. This is the one you want for messaging.
- Companion (USB) connects to a computer by cable.
- Repeater goes on a roof or a hill and passes other people's messages along.
- Room Server is a small bulletin board that others can post to.
- The first time you put MeshCore on a radio, choose the full install that erases it. Later updates don't need to.
- Click Flash, choose the radio's port in the pop-up, and wait for it to finish. Don't unplug it while it runs.
If the flasher can't see the radio, put it in download mode and try again:
- Heltec V3, V4, ThinkNode M2 and M5, T-Deck (ESP32 boards): hold the BOOT button while you plug it in.
- ThinkNode M1, T1000-E, RAK, T114 (nRF52 boards): press the reset button twice quickly. On the T1000-E, which has one button, hold it while you plug in the cable.
On the nRF52 radios, the flasher also offers the OTAFIX bootloader. Install it. It makes later updates over Bluetooth much more reliable.
Setting it up
When it restarts, the radio needs your region's settings. In the US and Canada the recommended preset is 910.525 MHz, SF7, BW62.5, CR5.2 Everyone near you has to use the same one, so ask your local mesh if you aren't sure.
Then pair it with your phone. If the radio has a screen, it shows the Bluetooth PIN. If it doesn't, the default PIN is 123456.
The app
You need an app on your phone to send messages. I made one: MeshCore++.
It works like an ordinary messenger. Pick a conversation, send a text, and see whether it was delivered. It only marks a message delivered when the other radio confirms it. It shows how many hops a message took. It has a map of repeaters, and a guide to choosing and setting up a radio. There is no account and no cloud. I wrote more about it here.
It is free on the App Store for iPhone, iOS 18 or later.
If you change your mind, the Meshtastic flasher puts Meshtastic back the same way. The two can't talk to each other, so pick the one your area uses.
Footnotes
- MeshCore FAQ, 6.6: https://docs.meshcore.io/faq/
- MeshCore FAQ: https://docs.meshcore.io/faq/